CSEC Technical Drawing Paper 1 May/June 2014 - Free CXC Past Paper with Answers

$\frac{1}{2}$ major axis

$\frac{1}{2}$ minor axis

Which of the following circles is correctly dimensioned?

If a scale of 1:100 is used in a drawing exercise, then an object 2 000 mm long would be represented on paper as

Which of the following drawings represents a scalene triangle?

If the perimeter of a rhombus is 152 mm, then the length of one side is

Item 7 refers to the following diagram. R PE FQ S

The diagram above shows part of the construction necessary for drawing an ellipse. What term describes the points E and F?

If a triangle with a perimeter of 198 mm is constructed with sides in the ratio of 2:3:4, then the SHORTEST side is

Which of the following instruments is used to quickly draw such items as bolt heads, nuts, and electrical and architectural symbols?

On which of the following planes is the 'plan' shown?

Which of the following methods of drawing an ellipse involves constructing a rectangle?

Which of the following illustrates how to bisect a straight line?

Which of the following correctly defines a locus?

The calculated circumference

A point which moves and traces a path

The area enclosed by two radii and an arc

A right-angled triangle wrapped around a cylinder

Which of the following statements BEST describes an equilateral triangle?

All the sides and angles are equal.

All the sides are equal but the angles are unequal.

All the sides are unequal but the angles are equal.

Neither the sides nor the angles are equal.

A quadrilateral with ONE pair of parallel sides is a

In the diagram above, the angle EFH is

The diagram above shows how to construct a triangle when given the

altitude and vertical angle

hypotenuse and one angle

altitude and the base angles

perimeter and vertical height

In the figure above, ABCDEF is a regular hexagon. What is the value of angle x?

In the diagram above, ABCD is a parallelogram. The triangle CDE is equal in area to

A triangle of perimeter 150 mm is constructed with a ratio of sides 2:3:5. Which of the following is the length of one of its sides?

In order to construct a tangent from the point P to the circle in the diagram above, one must FIRST

join P to a point on the circumference

join P to the centre

In the diagram above, the ratio of the area of EFGH to that of EGIJ is

The conic section at A above appears as

Which of the following are orthographic views of the diagram above?

To draw a circle to pass through the three given points, E, F and G, one MUST first

construct the tangents to the arc of the circle

draw a circle 30 mm in diameter

draw any chord and bisect it

construct chords EF and FG

The diagram above illustrates the proper method of

constructing an ellipse with trammel

finding the foci, the normal and the tangent of an ellipse

finding the focus of a parabola and the tangent at a point

constructing the hyperbola as a conic section

What is the length of EF in the construction above?

The bisector of the line AB is correctly shown by the drawing in

When preparing a drawing sheet, ALL horizontal lines are drawn with a

30°-60° set square

Which of the following illustrates the normal of an ellipse?

Which of the following constructions shows the procedure for drawing a perpendicular at the end of a line?

The diagram above shows the development of a truncated

Which of the following procedures is used when constructing the circumscribed circle of a triangle?

Draw any two chords.

Draw the extension of two sides.

Bisect any two angles.

Bisect any two sides.

Three sequential steps for drawing a tangent to a circle from any point outside the circle are I. Bisect the line which joins centre to point and draw a semicircle. II. Draw a circle and choose a point outside the circle. III. Join the centre to the point outside the circle. The correct order of the three steps is

In the diagram above, which of the labelled types of line indicates a cutting plane line?

Which of the following constructions shows the proper method of bisecting an angle?

Item 41 refers to the following diagram.

The lines marked X on the diagram above are symbols which indicate

the axes of symmetrical parts

that the edges are to be measured

that sections are to be removed

the continuation of the objects

Which of the following is a view of a right, square pyramid?

Which of the following diagrams illustrates the procedure for drawing a perpendicular ' to a line from a point outside the line?

The drawing above is to be reproduced in third-angle projection. On which of the following views can the distance, X, be measured? I. End II. Plan III. Front